Deutsch · English · Čeština · Polski · Hrvatski
♻ Experts4Recycling
Feasibility study · Concept · Pre-design

Feasibility studies with mass balance and 3D layout

Before you buy a site or apply for financing, you need to know which process, which plant and which costs your project requires. We work it through from the input to the end product.

Operators · Municipal waste companies · Investors · Project developers

Where plant projects go wrong at the early stage

The expensive mistakes in a recycling plant are rarely made on the construction site. Most of them are already in the first cost estimate.

📏

Capacity is calculated in tonnes only

Machines and conveyors are sized by volume. If throughput is stated only in t/h and an average bulk density is assumed, the volume flow of a light mixture comes out far too small. Belts that are too narrow and bottlenecks then only show up in operation.

💰

The costs come from one supplier quotation

A cost estimate built on a single budget quotation inherits that supplier's scope. Conveyors, steelwork, electrics and controls, dust extraction and buildings are then underestimated or missing altogether.

🏭

The building is checked last

Whether the line fits into the hall and the plot, with bunkers, platforms, maintenance access and escape routes, often only becomes clear in detailed design. By then the site and the budget are already fixed.

Scope of services

Four modules in a fixed sequence. Each builds on the one before, so every figure in the report can be traced back to its source.

A

Process and block flow diagram

The starting point is which fractions are to be produced, and in what quality.

  • Input recorded: origin, quantity, composition and range of variation
  • End products and the quality requirements of the off-takers defined
  • Block flow diagram with the separation task of each process stage
  • Technology options compared for each separation task, with strengths, limits and references
  • Agreed with you in iterations until the process is fixed
B

Mass balance and sizing

The mass balance sets the size of every machine and the width of every belt. That is why it comes before the layout.

  • Mass balance across all process stages in t/h and m³/h, using our own calculation tool
  • Volume flows summed per fraction, mixture densities derived from them
  • Separation parameters per machine with a source, or stated as an assumption
  • Yield and purity per end product, plus residual stream and its disposal route
  • Design case and load cases such as peaks or seasonal variation calculated separately
C

General arrangement and 3D layout

The layout shows whether the plant fits into the hall and the plot before a site is committed.

  • 3D layout in Autodesk Inventor from a parametric library of machines and conveyors
  • General arrangement drawing (GA) with main dimensions, platforms, bunkers and maintenance access
  • Conveyors with belt widths and inclinations taken from the mass balance
  • Fit into an existing building, or the building requirement for a new one
  • Process flow diagram (PFD) when the project moves on to tender or permitting
D

Costs, economics and permitting

With process, mass balance and layout in place, the cost estimate rests on quantities and line items.

  • Machine and consumer list with connected loads
  • Capital costs (CAPEX) per trade: machines, conveyors, steelwork, electrics and controls, dust extraction, civil works and infrastructure, with a list of assumptions
  • Operating costs (OPEX): staff, energy, wear, maintenance, disposal of residues
  • Business case with revenue per end product, payback and sensitivity to input quantity and product prices
  • Permitting route and required documents at the site: in Austria under AWG 2002 or GewO 1994, in Germany under the Federal Immission Control Act (BImSchG) and 4th BImSchV, in the formal or simplified procedure depending on waste type and throughput, elsewhere under the applicable national regulations

What you receive

Documents you can put in front of your management, the financing bank, a funding body or the authority.

  • Block flow diagram of the process
  • Mass balance in t/h and m³/h
  • General arrangement and 3D layout
  • Machine and consumer list
  • CAPEX and OPEX estimate with assumptions
  • Report with recommendation and next steps
The point: Every figure in the report leads back to a line of the mass balance or an item in the layout. That is what keeps the study standing when the bank or the funding body asks questions.

Why Experts4Recycling

📐

Engineering in-house

Block flow diagram, mass balance and 3D layout are produced by the same team. The cost estimate is built directly on these documents.

🔄

Both sides of the contract

More than 20 years in sorting and recycling plant engineering, on the supplier side and on the operator side. We know what a machine delivers and what is missing from a quotation.

🏗️

Through to the plant

On request, the study is followed by the tender, the permit application and support up to the performance test, all built on the same documents.

20+ yearsPlant engineering, supplier and operator side
70+ countriesProject experience on 4 continents
4 languagesEN · DE · FR · ES at negotiation level
t/h + m³/hMass balance by mass and volume, in-house tool

Studies and concepts, a selection

  • Austria: Feasibility study for the conversion and extension of a municipal waste logistics centre.
  • Austria: Concept and feasibility for the recovery of polyolefins as feedstock for chemical recycling and as refuse-derived fuel (RDF).
  • Austria and Germany: Design of sorting plants for polyolefins and lightweight packaging, from concept through permitting to acceptance and CE conformity.

We correspond in English or German.

Request an initial call

Tell us briefly what you are planning. We reply within 24 hours.

Please enter your first name.
Please enter a valid email address.
Please select your role.
Please select the project stage.
Please describe your project briefly.

Your data is treated confidentially and not passed on to third parties. We use it only to answer your request.

✅

Request received

Dipl.-Ing. Thomas Baldt will contact you personally within 24 hours.

For urgent matters you can reach us directly at
+43 664 73030310 – by phone or via WhatsApp – or at office@experts4recycling.com